key features: ? 1w output power ? miniature sip case ? 5,200 vdc isolation ? single & dual outputs ? >2.0 mhour mtbf ? -40c to +85c operation ? industry standard pin-out md100vhi miniature 1w, sip, very high isolation dc/dc con vert ers input parameter conditions min. typ. max. units input voltage range 5 vdc input 4.50 5.0 5.50 vdc 12 vdc input 10.80 12.0 13.20 15 vdc input 13.50 15.0 16.50 24 vdc input 21.60 24.0 26.40 input filter internal capacitor output parameter conditions min. typ. max. units output voltage accuracy 5.0 % output voltage balance dual output, balanced loads 0.1 1.0 % line regulation for v in change of 1% 1.2 % load regulation, see note 1 see model selection guide ripple & noise (20 mhz), see note 2 100 mv p - p temperature coef? cient 0.01 0.02 %/c output short circuit momentary (0.5 sec.) general parameter conditions min. typ. max. units isolation voltage 60 seconds 5,200 vdc isolation resistance 500 vdc 10 g? isolation capacitance 100 khz, 1v 7 pf common mode transient immunity 15 kv/s switching frequency 100 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +85 c operating temperature range case +100 c storage temperature range -55 +125 c cooling, see note 3 free air convection humidity rh, non-condensing 95 % physical case size see mechanical drawing (page 2) case material non-conductive black plastic (ul-94v0) weight 0.076 oz (2.4g) reliability speci cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25c, gnd benign 2.0 mhours absolute maximum ratings parameter conditions min. typ. max. units input voltage surge (1 sec) 5 vdc input -0.7 9.0 vdc 12 vdc input -0.7 18.0 15 vdc input -0.7 20.0 24 vdc input -0.7 30.0 lead temperature 1.5 mm from case for 10 sec 260 c caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. series www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com electrical speci cations speci cations typical @ +25?, nominal input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice.
pin single dual pin single dual 1+v in +v in 6 no pin common 2-v in -v in 7+v out +v out 5-v out -v out pin connections model selection guide micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 ? tel: (781) 344-8226 ? fax: (781) 344-8481 ? e-mail: sales@micropowerdirect.com www.micropowerdirect.com model number input output load regulation (% typ) output capacitive load (f max) ef ciency (%, typ) fuse rating slow-blow (ma) voltage (vdc) current (ma) voltage (vdc) current (ma, max) nominal range full-load no-load md105s-03vhi 5 4.5 - 5.5 286 35 3.3 303 20.0 1,000 70 600 md105s-05vhi 5 4.5 - 5.5 286 35 5.0 200 15.0 470 70 600 md105s-09vhi 5 4.5 - 5.5 266 35 9.0 111 10.0 470 75 600 md105s-12vhi 5 4.5 - 5.5 261 35 12.0 84 10.0 220 77 600 md105s-15vhi 5 4.5 - 5.5 254 35 15.0 66 10.0 220 78 600 md105d-05vhi 5 4.5 - 5.5 282 35 5.0 100 15.0 220 71 600 md105d-09vhi 5 4.5 - 5.5 269 35 9.0 56 10.0 220 75 600 md105d-12vhi 5 4.5 - 5.5 262 35 12.0 42 10.0 100 77 600 md105d-15vhi 5 4.5 - 5.5 254 35 15.0 33 10.0 100 78 600 md112s-03vhi 12 10.8 - 13.2 117 17 3.3 303 20.0 1,000 71 250 md112s-05vhi 12 10.8 - 13.2 117 17 5.0 200 15.0 470 71 250 md112s-09vhi 12 10.8 - 13.2 110 17 9.0 111 10.0 470 76 250 md112s-12vhi 12 10.8 - 13.2 108 17 12.0 84 10.0 220 78 250 md112s-15vhi 12 10.8 - 13.2 104 17 15.0 66 10.0 220 79 250 md112d-05vhi 12 10.8 - 13.2 116 17 5.0 100 15.0 220 72 250 md112d-09vhi 12 10.8 - 13.2 111 17 9.0 56 10.0 220 76 250 md112d-12vhi 12 10.8 - 13.2 108 17 12.0 42 10.0 100 78 250 md112d-15vhi 12 10.8 - 13.2 104 17 15.0 33 10.0 100 79 250 md115s-03vhi 15 13.5 - 16.5 95 16 3.3 303 20.0 1,000 70 200 md115s-05vhi 15 13.5 - 16.5 95 16 5.0 200 15.0 470 70 200 md115s-09vhi 15 13.5 - 16.5 89 16 9.0 111 10.0 470 75 200 md115s-12vhi 15 13.5 - 16.5 90 16 12.0 84 10.0 220 75 200 md115s-15vhi 15 13.5 - 16.5 84 16 15.0 66 10.0 220 79 200 md115d-05vhi 15 13.5 - 16.5 94 16 5.0 100 15.0 220 71 200 md115d-09vhi 15 13.5 - 16.5 90 16 9.0 56 10.0 220 75 200 md115d-12vhi 15 13.5 - 16.5 86 16 12.0 42 10.0 100 78 200 md115d-15vhi 15 13.5 - 16.5 84 16 15.0 33 10.0 100 79 200 md124s-03vhi 24 21.6 - 26.4 60 12 3.3 303 20.0 1,000 70 125 MD124S-05VHI 24 21.6 - 26.4 60 12 5.0 200 15.0 470 70 125 md124s-09vhi 24 21.6 - 26.4 56 12 9.0 111 10.0 470 75 125 md124s-12vhi 24 21.6 - 26.4 53 12 12.0 84 10.0 220 78 125 md124s-15vhi 24 21.6 - 26.4 52 12 15.0 66 10.0 220 80 125 md124d-05vhi 24 21.6 - 26.4 59 12 5.0 100 15.0 220 71 125 md124d-09vhi 24 21.6 - 26.4 56 12 9.0 56 10.0 220 75 125 md124d-12vhi 24 21.6 - 26.4 55 12 12.0 42 10.0 100 77 125 md124d-15vhi 24 21.6 - 26.4 53 12 15.0 33 10.0 100 78 125 notes: 1. output load regulation is speci ed for a load change of 20% to 100%. 2. when measuring output ripple & noise, it is recommended that an external ceramic capacitor (0.33 f typ.) be placed from the +v out to the -v out pins for single output units and from each output to common for dual output models. 3. free air convection is typically 20 lfm. the units should not be operated in still air (0 lfm). 4. operation at no load will not damage these units, however, they may not meet all speci cations. 5. it is recommended that a fuse be used on the input of a power supply for protection. see the table above for the correct rating. mechanical dimensions notes: all dimensions are typical in inches (mm) tolerance x.xx = 0.01 ( 0.25) pin 1 is marked by a ?ot or indentation on the unit derating curve
|
